Upholstering An Antique Chair

antique chair

I purchased this pretty gold chair from an estate sale.  I loved the gold detail. I instantly had a vision to reupholster it using an antique German grain sack. It was structurally sturdy, which is a very important thing to consider when purchasing a piece of furniture to rehab.  I have been enticed by furniture that needed some structural help in past, some of the time I can fix it, but other times I end up wasting a lot of time and money into a piece that ends up not being very functional.  I did notice that the padding needed to be replaced. The padding on the arms was pretty much nonexistent, and the seat had a crunchy feel to it.  I thought that it might be horsehair. I am not a fan of a crunchy feel in upholstering, so that needed to be fixed. This is an easy job that adds new life to a piece.  

To execute my vision, I purchased a German grain sack from one of my favorite shops, Objekts1.  There are a few other shops on Etsy that carry these special sacks, I find them with this search.  When working with this fabric I typically piece it togther with some plain vintage hemp.  This plain fabric can be found on Etsy.  The Germain grain sacks are expensive and this offers the ability to get several projects out of it.  I also love the look of the pieced togther complimentary fabrics. 

To begin my work, I removed the seat cover. I have learned the most about how to do upholstery from carefully disecting a piece. If you are a beginner carefully remove the old fabric and take notes and pictures on how it was placed and secured.  As always  I removed the staples of the original fabric with pliers and a small flathead screwdriver, careful to not harm the wood. Underneath the fabric what I found it wasn't horsehair, it was hay.  A lot of hay.  This made more sense, horsehair was used in some really high quality antique upholstery pieces, it usually isn't THAT crunchy when I find it.  It was past time to get rid of the hay seat in my opinion.

DIY upholstery

DIY Upholstery

Underneath the seat you never know what you are going to find.  In this case the springs were tied down perfectly with really strong twine.  That was a bit of good news.  I will and have retied springs on several occasions, its not a hard task, it can just take up a chunk of time.  But the webbing holding the springs in place was very frail.

DIY Upholstery

DIY upholsteryNew webbing versus old

 That needed to be replaced.  This is how I did it:

-I removed the old webbing.

DIY uphsoltery

-Using this webbing, I secured it with my staple gun with a 2-3 inch excess on the outside.  I folded this excess over and stapled it down to add further reinforcement.  I recommend using at least 1/2 inch staples for this step.  I use this staple gun with a compressor, it is great, but if you don't want to invest in a air compressor this staple gun will work.  It will take a bit more elbow grease and manipulating, but it will do the job.

DIY Upholstery

-Using a webbing tool like this one, I ran rubber side along the length of the webbing 5-6 times, this loosens up the fibers so I could get it really taut.  Then I use the scary, sharp side to pull the webbing as tight as possible across the bottom of the chair to the other side, when that is done I secure it with my staple gun the same way I did on the other side. I recommend using at least 1/2 inch staples for this step.  I use this staple gun with an air compressor, I really like it.  But if you don't want to invest in a compressor this staple gun will be okay, it takes a little more elbow grease and manuvering, but it will do the job.

DIY Upholstery

 

-I repeated this with all the strips of webbing, weaving the strips together in a basket weave pattern until it covered the bottom of the seat.

 

DIY Upholstery

-I was able to work around the springs without a problem. It did take some manipulating, but it worked and the ties were still in perfect condition so it saved me from having to retie them down. But generally the springs would be replaced following the webbing.  

-After the webbing was in place, the under side of the springs needed to be tied down to the webbing.  I used this 12 inch needle and tufting twine to stitch the springs in place.  I did 3 sets of stitches per spring, and doubled the stiching around each stitch. After this I could already feel the improvement in the seat.  It was time well spent. 

DIY Upholstery

DIY Upholsterynotice the white stitches of twine holding the springs in place

- I added a layer of burlap and stapled it down it on top of the springs.

DIY Upholstery

-On top of the burlap, I added a layer of 2 inch foam, I placed it on the seat and used it as a guide for cutting.  You could use the removed fabric as a pattern to cut the foam.

DIY upholstery  

-The next layer was a dacron, I stapled this in place with a few staples.

DIY Upholstery

-The final layer is the fabric, using the previous fabric as pattern I cut out my fabric.  I typically try to add about an inch when cutting just to make sure I have plenty.  I stapled this in place, stapling approximately every half inch.  I try to get as close to where visible wood part of the chair is so that it is easy to cover the staples with trim.  For this process I always have my pliers ready to remove the staples that end up in the wrong place, there are always a few of those.  It also helps to start with shorter staples, such as 1/4 inch staples that are easy to remove for the first few, then when it looks like the fabric is just how you want it use longer 1/2 inch staples to completely secure the fabric.

- To trim the fabric very close to the staples, I used these used these scissors.

-Then it was onto the back of seat. As I removed the fabric I also tried to keep the fabric intact so I could use it as a pattern, remember how I did this with the seat?  When I got the front of the back fabric off the previous foam that was in place it completely disintegrated, a sure sign new foam is needed. After cleaning that up I removed final piece of fabric that was used for the back of the back.  

DIY Upholstery

-Using the back piece of fabric as a pattern I cut a piece of new fabric that size.  I stapled this in place.  Typically with these chairs the back of the back is stapled to the front of the chair facing the back first, as pictured.

DIY Upholstery

DIY Upholstery

-For added stability I stapled in place some webbing as shown. I used the same process as the seat, but I didn't worry about completely covering this part with webbing, its just for a little added support.

DIY Upholstery

 

-Next I added a layer of 1 inch foam to the back, cut out using the old fabric pattern.   Then covered it with the fabric used for the front of the back, and stapled it into place using the same techinique as mentioned above with the seat. And trimmed up the fabric edges.

DIY Upholstery

DIY Upholstery

 

-I used this same process for the arms of the chair.

-One of the final steps was I adding trim.  I used this trim and for added texture I sewed it in a folded pattern.  I used a glue gun to secure it over the staples.  

DIY Upholstery

-Finally I added black dust cover fabric to the bottom of the chair.

DIY Upholstery

 

I decided to try adding a tufted cushion to the top of this chair.  These are the steps that I took to sew the cushion:

 -I used the fabric removed from the seat as a pattern.  I cut two pieces of canvas fabric about an inch bigger than the original fabric.  I sewed these two pieces together leaving a 3 inch opening, next I stuffed it with shredded memory foam (down feathers would work too) to create a full pillow. I sewed up the 3 inch opening.  When I sew anything upholstery related I sew two sets of stiches to offer added stability.  

DIY Tufted Cushion

- I covered this pillow with 2 layers of dacron and secured the it in place with a loose whip stitch using this needle and upholstery thread.

DIY Tufted Cushion

-Again using my orinigal fabric pattern I cut two pieces of my new fabric with 1 inch added to all sides. I used a 1/2 inch seam allowance when sewing, but cut the fabric 1 inch bigger than the seat pattern to allow for enough fabric to cover the height of the cushion.  I wanted this pillow to have an envelope closure, so I took one of those sides and cut it in half.  I added 3 inch strips of fabric to these pieces half pieces with a hem on the edge.  

DIY tufted cushion

DIY Tufted cushion

DIY Tufted Cushion

-  As added detail, I secured two pieces of trim to each corner where the legs were.  I pinned the trim in place so that at least 1/2 inch was on the outside (which will be inside when turned right side out), and about a 15 inches on the inside. 

DIY tufted cushion

- I took the two halves and lined them up so that they overlapped and lined up with the other complete piece of fabric.  I pinned the two sides together with the right sides in.

DIY tufted cushion

-With 1/2 inch seam allowance, I sewed the two pieces together.  I made small cuts just short of the seam on the corners to help the fabric to lie flat.

DIY tufted cushion

-After turning the cushion cover right side out I stuffed it in the cushion.  Next up is adding the tufts. I measured out the placement of the tufts and used pins to mark them.  I made sure to place three tufts to hold the envelope closure in closed.  I used this needle (I do think using a smaller guage long needle would have worked too) and tufting twine.  I started these tufts from the bottom and did two stitches per tuft crossing the stiches in a "X" on the top.  Then I pulled the twine as tight as possible on the bottom and did one tufting knot, next I added a tiny bit of glue from my glue gun on the knot to its barely visible and finish it with one more tufting knot.  Then I trimmed the twine to about a 1/2-1 inch in length from the knot.

-Finally I hemmed the trim on the ties for the legs to the desired length and then completed the tufted cushion. 

DIY upholstery

DIY upholstery

I am very pleased with the way this chair turned out. I brought it into the shop, Anthology Home, and it did sell.  I heard it went to a great home :). If you are more interested in purchasing a piece like this than reupholstering one yourself, if you are local to the Milwaukee area I will be selling more. Please email me if you have any questions, pennyandivydecor@gmail.com.